Previous Article

DIY Snake the Drain Tips

Next Article

DIY Wedding Projects

DIY Steps for Installing a Driveway Gate

The addition of a gate to the driveway of your home is a perfect way to provide additional security for you and your loved ones. It also brings a sense of personal style and visual drama that’s hard to beat. Learn the proper steps to install a driveway gate yourself.


  1. Set your hinge posts. The distance between your posts will depend upon the actual footage of your gate. For example, a 14-foot gate would have posts set 14 feet apart from center to center. Lay out your holes across your driveway the proper distance apart as per your manufactures instructions and remember to take into consideration the angle of the gate in the closed position. Usually, this angle will be perpendicular to the drive, but for some installations, this may vary. Dig your holes 12 to 18 inches in diameter. Remember to bell out the bottom of the hole and add a few doglegs to make sure your posts don’t tip; 34 inches is the standard depth for a posthole.

  2. Create your line level. A line level is used for determining where the bottom of the gate will be. Using your sledgehammer, drive in two metal stakes just beyond either side of the hole and in alignment to the angle you had determined earlier and tie a sting line tightly to the stakes. Place a line level on the string and adjust the string so that the string falls where you wish the bottom of the gate to. This should be two to four inches above the ground. 

  3. Mix your concrete. Your gate holes will typically require about 3 to 4 sacks of concrete per hole. Put your concrete into a wheelbarrow and begin mixing. This is easier to accomplish if you have a friend to help you as it is faster. Add the water to the concrete a little at a time. You want the mixture stiff enough to set the post in place, yet loose enough to settle into the hole and around the posts.

  4. Sink the first hinge post. There should be a label on the post that denotes the bottom of the gate. Place the line of that label so that it lay exactly even with the level string line you had attached to the metal stakes. One person must hold the post still and steady while another shovels the concrete into the posthole and around the post. The person holding the post should hold a level against each side of the post to make sure the post is, and stays, plum. This must be checked on both sides of the post and be done several times to ensure a straight set post.

  5. Set the second hinge post. Place the second hinge pole into its hole and use a tape measure to ensure that your posts are exactly the length apart from inside to inside that they should be according to your gate width and your make and model. Once measurements check out, set the second hinge posts label to the proper string level height as you did previously. Double check all measurements then fill in the second posthole with concrete using the same method outlined above.

  6. Re-measure. Once the second hinge post is set and plumbed, recheck the distance between the posts by measuring between the bottoms of the posts. There is a tolerance of approximately ½ an inch for this particular measurement. You will now measure between the hinge posts again between the tops of the posts. The distance between the top and the bottom of the posts should be exactly the same. Allow posts to cure overnight before continuing.

  7. Attach your hinges. Your gate assembly will come with pre-packaged finials and bolts. These bolts attach directly to pre-drilled holes located in your hinge posts. Attach all four hinges and tighten them securely, but not too tight lest the nut inserts turn within the post. Make sure you find the grease fitting for each hinge and thread it carefully in place. Your hinges should be greased at least once a year in order to keep the hinges properly lubricated. 

  8. Hang your gate. Back off the outside hinge nuts and run the top and bottom hinge bolts through the holes in the gate itself. It is helpful to have someone help you maneuver the gate around while doing this step. Once the gate is on, replace the hinge nut again and finger tighten it. Do this for top and bottom. Repeat with the other side of the gate.

  9. Attach your finials. Apply a line of liquid nails or silicon caulk around the inside of your finial housing and attach it to the top of the hinge post. Repeat on the other side.