Steps to Install New Windows
New windows do more than just add a fresh look to your home, they also help to conserve energy. With a little bit of help and some know-how, you can install new windows yourself. By doing so, you not only save some money but you also earn bragging rights for accomplishing a moderately difficult home improvement task.
By installing new windows in your home, you help to conserve energy. Today's windows come in a variety of different energy efficiencies and are double or triple paned, low-e, and tinted. Installing them correctly ensures that you reap the benefits that new windows provide. No matter what type of window you decide to install, here are some fool-proof ways to do so to ensure that they are installed properly.
Before starting a new window installation project, it is best to know the terminology of the job.
Definitions:
Rough Opening: A framed opening in a wall where a window will be installed. This measurement should be slightly larger than the actual window that will fit in its opening.
Shims: Often made of wood, used to make something level, or to adjust something to make it fit properly.
Plumb: A measurement that is true to a vertical plane.
Waterproof Membrane: An impermeable layer of plastic film, or other material, adorned with adhesive, and placed to stop the transfer of, or the absorption of water.
Nailing Fin: Found on the window unit, a plastic strip used for installing a window, though which nails are driven.
Window Jamb: Generally referred to the side of the window that houses the tracks of the window that allows for the window to open and close.
Window Flashing: Material installed over, and used to deflect water penetration of, windows.
Tools and other items you will need to install a new window:
New Window
Shims
Waterproof Membrane
Nails
Hammer
2 and 4 Foot Levels
Measuring Tape
Caulk
Insulation
If you will be making your own window flashing, you will also need:
Piece of thin metal
Metal cutters
How to install a new window:
Measure the rough opening.
The measurements needed will be the width of the areas of the window that include the top, middle, and bottom. As well, measurements of both sides and middle, lengthwise, should be taken. Take the amounts of measurements from the three taken width-wise and then subtract the three taken lengthwise. If the difference between the two measurements are more than one inch, then you will need to apply shims to make up the difference where the rough opening is not level or not plumb.
Choose your new window measurements so that they are within 3/4 inches narrow at the smallest width measurement and 1/2 inch shorter than the smallest height measurement. Otherwise, you may find yourself re-framing the entire window opening.
Apply a waterproof membrane.
Beginning at the bottom vertical plane of the rough opening, remove adhesive protecting paper and apply a waterproof membrane strip that centered and extends 9 to 12 inches on either side of the opening. Using the center method, now apply waterproof membrane to both sides of the rough opening, extending each piece 6 inches beyond the opening and overlapping the piece applied upon the bottom vertical plane. Finally, apply the waterproof membrane across the top of the rough opening width wide, again using the center method, and extend the piece 6 inches on either side, overlapping the pieces just applied to the sides of the rough opening. It is important to remember to overlap all pieces and work from the bottom and up. This ensures that water runs down, over the membrane and not under it.
Place window into rough opening.
From outside the home, slip open the nailing fins and place the window onto the bottom window sill. Have a friend, a neighbor, or other home improvement enthusiast stand inside and let you know when the gaps on either side of the rough opening look the same. At this point, tack the nailing fin in place but do not drive the nail all the way in. This will allow for adjustments to be made but will also keep the window in place.
Check for level.
Using a 2 foot level, check for a side of the window that is higher than the other. On the side that was higher, hold a 4 foot level against the side window jamb. Shift the window sill in the direction needed until the level shows that the jamb is plumb. Tack another nail into the bottom of the windows nailing fin on the same side that the first nail was tacked into. Using the 2 foot level again, check the bottom sill for level, adjusting the free bottom corner up as needed. Tack another nail into the window nailing fin in this bottom corner.
Check for square.
Measure the window frame, diagonally, first left to right from one bottom corner, then right to left from the opposite corner. The measurements should be the same, or within 1/16th of an inch of each other. To make any adjustments, remove the last two tacked nails and then re-tack when measurements are correct. Now, measure the window width-wise in several points, making sure that those measurements are also equal to each other. Drive nails completely into the framing, along the nailing fins pre-punched holes, making sure to drive the tacked nails as well. Start on the sides, and then complete nailing at the top and bottom.
Apply waterproof membrane over nailing fins.
Using the same method used to apply the weather membrane as before, install the waterproof membrane over the nailing fins. Start at the bottom, use the center method, and extend the waterproof membrane 6 inches on either side. Then, apply to the sides, and finish with the top. Be sure to overlap the seams, so that water will run over the membrane and not behind it.
Apply window flashing.
Using either the window manufacturer's supplied metal flashing, or a piece of flashing cut by you, install over the top of the window. To install this piece, use a bead of caulk to the top edge of the window. Then, place the flashing into the bead of caulk.
Insulate around the window.
From inside the house, use either bat-insulation or expanding foam and fill in any gaps between the window and framing. If using foam, take your time and fill the gap slowly. This will allow the foam to expand and cure properly. You can add more as needed following the curing time.
Installing a new window in your home takes a little time and patience but the rewards are worth the effort.