9 Essential Equipment Items for Managing Workplace Spills
A spill plan is only as useful as the equipment behind it. Procedures and training tell your team what to do. The gear decides whether they can actually do it quickly, before a small leak turns into a much bigger clean-up.
Good workplace spill management comes down to having the right equipment in the right place, matched to what you store. Here are the nine items worth having on site.
1. Spill Kits Matched to What You Actually Store
Spill kits generally come in three types:
- General purpose kits handle oils, coolants and most non-aggressive liquids.
- Oil-only kits absorb hydrocarbons but repel water, so they work in wet areas and outdoors.
- Chemical kits are built for acids, alkalis and other aggressive substances.
It’s tempting to buy one generic kit for the whole site, but it won’t suit every substance you store. An absorbent that works on oil may not be safe to use on an acid, so check the Safety Data Sheet (SDS) for each product before choosing a kit. Size each kit to the largest spill you could realistically face in that area. Keep it next to the hazard, not in a storeroom at the other end of the building.
2. Bunding and Spill Pallets for Drums and IBCs
A spill kit deals with liquid that’s already on the floor. Bunding stops it getting there.
Bunding is secondary containment: a second barrier that catches whatever escapes the primary container. For drums and intermediate bulk containers (IBCs), bunding spill pallets sit directly under the containers, with a sump that holds any leak. A failed tap or split seam stays put instead of running across the shift floor.
Capacity is the first thing to check. The sump should hold the full contents of the largest container sitting on it, and the rules for your chemical type and location may require more. Check what applies to you before you buy.
Compatibility comes next. The pallet should be made from a material that won’t be damaged by what it holds. Incompatible chemicals also shouldn’t share a sump, because acids and alkalis on the same pallet turn one problem into two.
3. Absorbent Pads, Socks and Booms
These are the consumables, and each shape does a different job. Pads soak up drips under machinery and small puddles. Socks are long and flexible, so you can ring a spill with them to stop it spreading while you work inward. Booms handle bigger volumes and outdoor areas.
Keep spares beyond what’s in the kits. A kit that was used last month and never restocked is just a wheelie bin with a label on it.
4. Drain Covers and Drain Protection
A chemical that reaches a stormwater drain can end up in local waterways, well beyond your site and well beyond your control.
Drain covers are heavy, flexible mats that seal over a grate. They take a moment to put down, and they buy you time to contain the spill properly. Mark every drain on your site plan as well. Liquid running towards a drain is the wrong moment to find out where the drains are.
5. PPE Chosen From the Safety Data Sheet
The SDS for each product sets out the protective equipment needed to handle it. Use it. A glove that holds up against one chemical can break down against another, so “we’ve got gloves” isn’t a spill plan.
A typical chemical spill PPE set covers several items:
- Chemical-resistant gloves
- Splash goggles or a face shield
- A chemical-resistant apron or coveralls
- Suitable boots
- Respiratory protection, where the SDS calls for it
Store it with the spill kit, so no one has to go hunting.
6. Emergency Eyewash and Shower Stations
If a chemical can splash, people need somewhere to flush it off, fast. Eyewash and shower stations should sit close to the hazard, with a clear, unobstructed path to reach them. They should also be able to keep flushing for as long as the SDS recommends.
Test plumbed units regularly so they work when they’re needed. Where there’s no plumbing nearby, a self-contained portable unit fills the gap. Check and replace its fluid according to the manufacturer’s instructions, and make sure your equipment meets the current relevant Australian Standard.
7. Signage, Barriers and Response Charts
The first job in any spill is keeping people out of it. Cones, barrier tape or portable barriers let your team cordon off the area quickly. That keeps forklifts and foot traffic from tracking contamination across the site.
A short written procedure fixed to each kit helps too: stop the source, contain the spill, clean it up, dispose of the waste and report it. Under pressure, people follow what’s in front of them.
8. Labelled Waste Containers for Used Absorbents
Used absorbent carries whatever it soaked up, so handle it with the same care as the chemical itself. Contaminated pads don’t belong in the general bin.
Keep heavy-duty disposal bags and sealable, clearly labelled containers with each kit. Dispose of the waste in line with your local environmental requirements.
9. An Up-to-Date Chemical Register and SDS File
It isn’t hardware, but every other item on this list depends on it. Keep a current list of the hazardous chemicals on site, with the latest SDS for each one, somewhere your team can reach it quickly. Those documents tell you which kit, which PPE and which first aid response each chemical needs.
Once they’re in place, run a short spill drill, so the first time anyone opens the kit isn’t during a real incident.
Checking Your Workplace Spill Management Setup
Walk the floor and stop at every point where chemicals are stored or decanted. At each one, ask yourself two questions. If a container failed right here, where would the liquid go? And how long would it take someone to get the right kit and PPE to it?
If the answer to the first is “the drain” or “across the walkway”, start there. Containment is the next piece of equipment to sort out.