Previous Article

How to Make a Cotton Shag Rug

Next Article

How to Make a Jersey Shag Rug

How to Make a Jean Shag Rug

When you’re looking for a way to put a little color and personality into a room, the addition of a simple rug can go a long way in opening up a space and providing a bit of panache. But if you’re one of those fiercely independent and highly artistic types, chances are that settling on a rug created by someone just isn’t an option.

Items Needed:



  • Spray adhesive

  • Large upholstery needle or large leather needle

  • Hot glue gun with long, narrow nozzle and wash-resistant glue sticks

  • Old blue jeans cut into 3/8 inch wide x 6 inches long

  • Seam edges of jeans plus 1 inch fabric on either side

  • Gridded matting

  • Measuring tape

  • Sharpie pen

  • Scissors

  • Drop cloth


 





  1. Measure your rug. Use a measuring tape to figure out how large you want the rug to be. Use your sharpie pen to create cutting guides that follow your measurements and then simply cut your rug out away from the rest of the matting.

  2. Wash the jeans. If the jeans are bleeding dye, run them through a cold wash cycle and add two cups of vinegar to the final rinse cycle. If your washer offers a "soak" option try letting it soak in the vinegar for a half an hour to give it extra time to try and set the dye before rinsing and spinning it out. Rinse twice and dry on high heat to allow for shrinkage. 

  3. Cut the fabrics into strips that are 3/8 an inch wide and roughly six inches long. You want to have enough room to work with so that you can comfortably tie a knot in the middle. Add a little extra length if you need it. Make a thick, luxurious rug by cutting either end right down the middle, stopping an inch or two from the center on either side. 

  4. Do not cut the seams that run along the inside or outside of the legs into strips for your rug. Instead, cut them into two or three-foot sections, or longer if you have the length to do so. Preserve both the seams, and roughly a half-inch to 1-inch of jean material on either side of each seam. Trim them and set them aside as you will be using them later to bind the edges of your rug.

  5. Add a design or pattern if you want one. If you want a design to fill in, large stencils work well. Just trace them on to the matting with a sharpie pen. Designs and patterns that look good in a cross stitch also work well. Keep any design very simple, as this is your first rug. 

  6. Leave the first inch of the entire mat border free of fabric strands as that is where the binding will go. Pick up a single strip of denim and select two side-by-side holes on the grid mat where you would like to begin. Thread each end of the strip through the holes from the bottom of the grid. Pull the strands up through the holes and tie them together in a small, tight knot.

  7. Add a small bead of hot glue to the center of the knot you’ve created and tie the ends together a second time, this time creating a knot on top of the bead of hot glue. Move on to the next strand.

  8. Repeat step 7 until your entire mat is filled with tied-off strands except for the one-inch border along the outer edge of the mat.

  9. Follow your pattern with your different shades of denim as you go, if applicable. It may be helpful to separate your denim colors in advance if planning on working with a pattern or design.

  10. Pick up your new rug and flip it upside down to give it a good shake to straighten most of the pile. This will make it easier to trim. Remember that you will be deliberately fraying this rug to create additional textured "shag." Unraveling is not possible due the knotting method you used to create your pile; however, fraying will have an effect on the rug that will need to be considered prior to trimming. Long frayed shag looks interesting and feels soft underfoot, yet it can tangle easily if care it is not taken care of. Short fray shag has a fun and funky look and feel and holds up much better under traffic than long fray shag. A medium height fray pile has a bit more cushion underfoot than short fray pile and holds up against fair traffic, though it does still tangle upon occasion. When you have decided the length you want, use your scissors to start trimming the pile of your rug. Begin at the corner of a short side and work your way back and forth until you reach the other short side end. Step back and check your progress often to make sure you aren’t removing too much from any one area. 

  11. Bind your edges by spraying the "wrong side" of the jean seams you saved with spray adhesive. Lay these items on top of a plastic drop cloth or clean garbage bag to protect your carpet or flooring while spraying. Hold the can no further than 8 inches from the surface of the wrong side of the seams and apply a light, even coat. Wait 30 seconds for it to cure then apply a second light, even coat. Do not overspray.

  12. Begin working from the outside center of the rug on a long side and slide one edge of the jean seam under the body of the rug. Carefully fold over the other side of the seam strip on to the top portion of the grid that was left empty of fibers. Use your fingers to firmly and steadily press the two sections both to the grid mat and to each other through the holes provided on the mat. You want at least a quarter-inch overhang of seam material beyond the hard surface of the mat border. Continue working all the way around until the border is covered with the seamed binding edge. 

  13. Knot the binding edge on to the mat grid. Thread a strand of jean fabric on to the large upholstery needle and use the needle to fit your strand up through the holes underneath the grid mat that is now covered with the seam rug binding. Thread through one end at a time, or if you have two large needles, thread both ends up through the bottom holes and through the fabric. Tie off and glue as usual.

  14. Completely fill the vacant squares in using the upholstery needle and tying the strands off until all you see at the edges are the seams of a pair of jeans binding the edges of your rug. Binding the seam fabric by threading and knotting strips through the grid ensures that it will remain firmly bound for the life of the rug.